10/20/40 End fed antenna kit, including 100 Watt 1:49 impedance transformer

 31,50 43,50 Incl. VAT

(9 customer reviews)

10/20/40 meter band end fed antenna kit, including 100 Watt 1:49 impedance transformer, wire of your choice, DIY kit

Click here for an extensive construction manual of the 1:49 impedance transformer

This kit contains all parts to make a 10/20/40 meter band end fed antenna.

With a handy fixing plate for the toroid, so no longer necessary for gluing.

Total length approx 12 meters.

See the complete parts list and details about the antenna wire at the bottom of the page in the product description section.

Select your antenna wire below!

Categories: , SKU: N/A

Description

10/20/40 End fed antenna kit, including 100 Watt 1:49 impedance transformer, Wire of your choice, DIY kit

An advantage of an end fed antenna is of course the simplicity, especially for field work this is a huge advantage. Put a telescopic mast against a pole, hook the antenna to the top and slide out. This will allow you to be in the air within 5 minutes! An additional advantage is that the 10/20/40 endfed antenna can easily be vertically polarized. This makes the antenna convenient for (DX) long distance connections. The 10/20/40 End fed Antenna kit has a total length of approximately 11.9 meters. From the feed point first 10.1 meter antenna wire then a coil of about 35 uH and then another little 2 meters of wire.

The feed point of the 10/20/40 end fed antenna kit is a broadband impedance transformer. Because the End Fed wire antenna has a very high impedance +/-2500 Ohm, an impedance transformation is needed. By means of a winding ratio of 1:7, this impedance is transformed to an impedance of 50 Ohm.

Click here for an extensive construction manual of the 1:49 impedance transformer

This End Fed antenna comes with antenna wire of choice:

Experimental Wire: This wire consists of 1.0 mm2 braided copper wire with a UV resistant black shield. The total diameter is about 2 mm. Perfect for experiments or holiday antennas. Because the core only consists of copper, this wire will stretch over time and continue to hang. The tensile force of this wire is thereby also limited.

Copper/Kevlar Wire: This antenna wire is produced especially for HF Kits in the Netherlands. The wire consists of a Kevlar core with around 1.1 mm2 tinned copper braiding. 1x 0,4 mm Kevlar en 24x 0,25 mm copper. The insulator consists of black UV resistant PE. The total diameter is about 2.5 mm. Tension force approx. 50 kg. In this way a strong, smooth and relatively light antenna wire is obtained.

Copper/Stainless Wire: This antenna Wire is produced especially for HF Kits in the Netherlands. The wire consists of a stainless steel core (7x 0, 35mm) with around 1.0 mm2 tinned copper braid. 7x 0.3 mm stainless steel and 14x 0.3 mm thinned copper. The insulator consists of black UV resistant PE. The total diameter is about 2.5 mm. Tension force approx. 100 kg. This is a robust antenna wire with a very long life span. As far as we are concerned, this is the best choice for permanently placed antennas.

This kit includes:

Antenna:

  • 12.5 meter antenna wire of your choice
  • 19 mm PVC Pipe for coil
  • 5.50 meter 0.75 mm winding wire for the coil
  • 25 mm heat shrink sleeve for coil insulation
  • 2x Stainless Steel Cable Clamp
  • 1x End Isolator
  • 1x Cable lug 5mm
  • 1x Heat shrink sleeve for cable lug

1:49 Impedance transformer:

  • IP65 enclosure 82x80x55 mm
  • Ferrite toroid Amidon FT140-43
  • Winding Wire 1.00 mm
  • 100 pF Capacitor 1kV
  • PL 259 Chassis
  • Toroid mounting plate
  • Stainless steel M3 6mm screws 4x
  • Stainless steel M3 Spring washer 4x
  • M3 Cable lug
  • M5 Cable Shoe
  • Stainless steel (A4) M6 strain relief
  • Stainless Steel M6 Nut
  • Stainless Steel M6 washer
  • Stainless steel M6 Spring washer
  • Stainless Steel M5 Bolt 25mm
  • Stainless steel M5 Wing nut
  • Stainless Steel M5 nut 2x
  • Stainless Steel M5 washer 2x
  • Stainless steel M5 Spring washer 2x
  • Stainless steel M5 tooth washer 2x
  • Stainless steel M3 Bolt 12mm 4x
  • Stainless Steel M3 Nut 4x
  • Stainless Steel M3 Washer 4x
  • Stainless steel M3 tooth washer 4x

Tips:

  • As much as possible, Hang the antenna free from interfering elements
  • This antenna can also be used as a sloper.
  • In case of common mode issues, use a common mode choke. Do not place this choke directly at the feed point of the antenna.

Additional information

Antenna Wire

Experiment wire, Copper/Kevlar wire, Copper/Stainless steel wire

9 reviews for 10/20/40 End fed antenna kit, including 100 Watt 1:49 impedance transformer

  1. Dutch

    THEO (verified owner)

    Dit bouwkitje besteld, en de volgende dag in huis.
    Moet zeggen het ziet er allemaal verrassend goed uit.
    Ook het gevreesde printplaatje voor de rinkern lijkt me een handige oplossing voor de ringkern goed vast te zetten.
    De meeste onderdelen zitten mooi apart in zakjes wat bij elkaar hoort.
    Mijn eerste indruk 5 sterren, en de prijs is ook niets mis mee.
    Nu het bouwen en testen nog! 🙂

  2. Dutch

    Lennard (verified owner)

    Snelle levering, duidelijke bouwbeschrijving, bouwpakket is ook zeker voor de beginner goed te doen. Zojuist met deze antenne een verbinding op 20 meter via SSTV met Rusland gemaakt. Prijs kwaliteit verhouding is super. Voor mij 5 sterren waard.

  3. Dutch

    THEO (verified owner)

    Eindelijk goed weer, dus tijd om de boel af te regelen!
    Ik heb de maten van de tekening aangehouden behalve de lengte achter de spoel, die viel bij mij wat kleiner uit. Moet wel zeggen hij staat verticaal aan een Spider mast. Op 10 meter moet het kastje een stukje van de grond af dan krijg ik een swr van 1 op 1,2 tot 1 op 1,5 de andere banden ligt de meter plat. De eerste verbinding was gelijk met Ukraine met goed rapport. Al bij al een super antenne voor dat geld. Ook een beginner zal deze antenne zelf kunnen maken. Ook de materialen zijn van goede kwaliteit zoals het roestvrij staal. Daarom ook 5 sterren.

  4. Dutch

    Rick Minderhoud (verified owner)

    Werkt fantastisch. als beginnende luisteramateur deze antenne besteld.
    bouwen was voor de eerste keer een leuk project.

    zeker de moeite waard!

  5. Dutch

    Benny (verified owner)

    Super service en nette kit om in de avonduurtjes in elkaar te zetten. Duidelijke beschrijving.

  6. Dutch

    Hans mentink

    Hier het 49.1 balun besteld en in elkaar gezet.
    In de mast aan een aluminium buis horizontaal gemonteerd en wel aan aarde gelegd.
    Aardpen zit 9 meter in de grond.
    Zelf zwart installatie draad eraan dan coil en 1.83mtr draad.
    Swr op 20 meter 1.8 op 1 .
    40 meter 1.6 op 1
    Tussen transciever en balun zit 9mtr rg 58.
    Ben zeer tevreden.
    Maximale afstand gewerkt van 10700 km palou

  7. English

    Sofia (verified owner)

    Fun to build and works like a charm! No need for a tuner.

  8. Dutch

    Jeffrey peters (verified owner)

    Mooie kit duidelijke handleiding en makkelijk te bouwen. Verzending ging ook super snel volgende dag al in huis.

  9. Dutch

    mikkenie (verified owner)

    De 10/20/40 Endfed besteld en binnen 2 dagen al in huis (besteld op een Zondag). De eerste indruk van de kit is uitstekend. Het scheelt gewoon een hoop zoekwerk langs meerdere winkels. Het materiaal is goed. De bouw van de 100W UNUN was goed te doen. Met de spullen daarna (letterlijk) het veld in (het veengebied bij Eemnes, JO22PG) De antenne aan een horizontale draad (zonweringkoord) op ongeveer 1,5 meter hoogte gehangen (tussen een paaltje en een fiets) en met de antenne analyzer op 20m in de band gezet. SWR is ongeveer 1:1 (SWR meter doet ‘niets’). Dezelfde vooravond nog enkele verbindingen binnen Europa kunnen maken met slechts 5 Watt SSB. Onder de gehoorde landen: Japan, Canada, VS, Brazilië, Noord Afrika, Rusland en grote delen van Europa. Het werkt dus. De spoel en 40m ‘staart’ komen later. Die band is toch nog dicht. Een aanrader. Vooral voor wie voornamelijk portabel wil uitkomen op HF.

Show only reviews in English (1)

Add a review

Your email address will not be published. Required fields are marked *

Post comment

You may also like…