10/(15)/20/40/80 Endfed antenna wire set, Wire of your choice

 16,00 36,00 Incl. VAT

10/(15)/20/40/80 EndFed antenna wire set including coil – Wire of your choice

Do you have an EndFed antenna in a different version, but you also want to experiment with other wire lengths? HF Kits now offers EndFed antenna wire sets. The 10/(15)/20/40/80 Endfed antenna wire set has a total length of about 23 meters. From the feed point first 20.4 meter antenna wire then a coil of approximately 110 uH and then another +/- 2.5 meters wire.

Click here for an extensive construction manual of the 1:49 impedance transformer

Total length approx. 23 meters.

See the complete parts list and details about the antenna wire at the bottom of the page in the product description section.

Select your antenna wire below!

Description

10/(15)/20/40/80 EndFed antenna wire set including coil – Wire of your choice

Do you have an EndFed antenna in a different version, but you also want to experiment with other wire lengths? HF Kits now offers EndFed antenna wire sets. The 10/(15)/20/40/80 Endfed antenna wire set has a total length of about 23 meters. From the feed point first 20.4 meter antenna wire then a coil of approximately 110 uH and then another +/- 2.5 meters wire.

Click here for an extensive construction manual of the 1:49 impedance transformer

This 10/(15)/20/40/80 EndFed antenna wire set comes with antenna wire of your choice:

Experimental Wire: This wire consists of 1.0 mm2 braided copper wire with a UV resistant black shield. The total diameter is about 2 mm. Perfect for experiments or holiday antennas. Because the core only consists of copper, this wire will stretch over time and continue to stretch. The tensile strength of this wire is therefore also limited.

Copper/Kevlar Wire: This antenna wire is produced especially for HF Kits local in the Netherlands. The wire consists of a Kevlar core with around 1.1 mm2 tinned copper braiding. 1x 0,4 mm Kevlar en 24x 0,25 mm copper. The insulator consists of black UV resistant PE. The total diameter is about 2.5 mm. Tension force approx. 50 kg. In this way a strong, flexible and relatively light wire is obtained.

Copper/Stainless steel Wire: This antenna Wire is produced especially for HF Kits local in the Netherlands. The wire consists of a stainless steel core (7x 0, 35mm) with around 1.0 mm2 tinned copper braid. 7x 0.3 mm stainless steel and 14x 0.3 mm thinned copper. The insulator consists of black UV resistant PE. The total diameter is about 2.5 mm. Tension force approx. 100 kg. This is a robust antenna wire with a very long life span. As far as we are concerned, this is the best choice for permanently placed antennas.

This 10/(15)/20/40/80 EndFed antenna wire set contains:

  • 24 meters Antenna litze of your choice (21 + 3)
  • 19 mm PVC Pipe for coil
  • 11 meter 0.50 mm winding wire for the coil
  • 25 mm heat shrink sleeve for coil insulation
  • 1x End Isolator
  • 2x Stainless Steel Cable Clamp
  • 1x Cable lug 5mm
  • 1x Heat shrink sleeve for cable lug

Tips:

  • As much as possible, Hang the antenna free from interfering elements
  • This antenna can also be used as a sloper.
  • In case of common mode issues, use a common mode choke. Do not place this choke directly at the feed point of the antenna.

Additional information

Antenna Wire

Experimental Wire, Copper/Kevlar Wire, Copper/Stainless steel Wire

Reviews

There are no reviews yet.

Be the first to review “10/(15)/20/40/80 Endfed antenna wire set, Wire of your choice”

Your email address will not be published. Required fields are marked *

Post comment

You may also like…